__ __ __ __ _____ _ _ _____ _ _ _ | \/ | \ \ / / | __ \ (_) | | / ____| | | | | | \ / |_ __\ V / | |__) | __ ___ ____ _| |_ ___ | (___ | |__ ___| | | | |\/| | '__|> < | ___/ '__| \ \ / / _` | __/ _ \ \___ \| '_ \ / _ \ | | | | | | |_ / . \ | | | | | |\ V / (_| | || __/ ____) | | | | __/ | | |_| |_|_(_)_/ \_\ |_| |_| |_| \_/ \__,_|\__\___| |_____/|_| |_|\___V 2.1 if you need WebShell for Seo everyday contact me on Telegram Telegram Address : @jackleetFor_More_Tools:
# udev-workflow.sh
#
# udev workflow for Relax-and-Recover
#
# This file is part of Relax-and-Recover, licensed under the GNU General
# Public License. Refer to the included COPYING for full text of license.
if [[ "$VERBOSE" ]]; then
WORKFLOW_udev_DESCRIPTION="udev handler; triggered by udev rule"
fi
WORKFLOWS+=( udev )
WORKFLOW_udev () {
# Do nothing in simulation mode, cf. https://github.com/rear/rear/issues/1939
if is_true "$SIMULATE" ; then
LogPrint "${BASH_SOURCE[0]} is a udev handler; triggered by udev rule"
return 0
fi
# If no udev workflow has been defined, exit cleanly
if [[ -z "$UDEV_WORKFLOW" ]]; then
Log "Variable UDEV_WORKFLOW not set, skipping udev workflow."
return
fi
WORKFLOW="$UDEV_WORKFLOW"
# Triggered by block-device, so force OUTPUT
OUTPUT=USB
# Set USB_DEVICE based on ID_FS_LABEL or UDEV DEVNAME
if [[ "$ID_FS_LABEL" && -b "/dev/disk/by-label/$ID_FS_LABEL" ]]; then
Log "Using USB or disk device based on udev ID_FS_LABEL '$ID_FS_LABEL'"
USB_DEVICE="/dev/disk/by-label/$ID_FS_LABEL"
elif [[ "$DEVNAME" && -b "$DEVNAME" ]]; then
Log "Using USB or disk device based on udev DEVNAME '$DEVNAME'"
USB_DEVICE="$DEVNAME"
else
Log "We cannot determine USB or disk device from udev, using configuration"
fi
# If udev workflow does not exist, bail out loudly
has_binary WORKFLOW_$WORKFLOW || Error "Udev workflow '$UDEV_WORKFLOW' does not exist"
# Turn the UID led on
if has_binary hpasmcli && [[ "$UDEV_UID_LED" =~ ^[yY1] ]]; then
hpasmcli -s "set uid on" >/dev/null
fi
# Run udev workflow
WORKFLOW_$UDEV_WORKFLOW "${ARGS[@]}"
# Blink the UID led and turn it off
if has_binary hpasmcli && [[ "$UDEV_UID_LED" =~ ^[yY1] ]]; then
hpasmcli -s "set uid off" >/dev/null; sleep 0.5
hpasmcli -s "set uid on" >/dev/null; sleep 0.5
hpasmcli -s "set uid off" >/dev/null; sleep 0.5
hpasmcli -s "set uid on" >/dev/null; sleep 0.5
hpasmcli -s "set uid off" >/dev/null
fi
# Suspend USB port (works fine on RHEL6, fails on RHEL5 and older)
if [[ "$DEVPATH" && "$UDEV_SUSPEND" =~ ^[yY1] ]]; then
path="/sys$DEVPATH"
Log "Trying to suspend USB or disk device at '$path'"
while [[ "$path" != "/sys" && ! -w "$path/power/level" ]]; do
path=$(dirname $path)
done
if [[ -w "$path/power/level" ]]; then
Log "Suspending USB or disk device at '$path'"
echo -n suspend >$path/power/level
fi
fi
# Beep distinctively
if [[ "$UDEV_BEEP" =~ ^[yY1] ]]; then
### Make sure we have a PC speaker driver loaded
if grep -q pcpskr /proc/modules || modprobe pcspkr; then
Log "Beep through PC speaker."
if has_binary beep; then
# After testing in a noisy datacenter, this seems the best
# (although it takes up 4 seconds)
beep -f 2000 -l 1000 -d 500 -r 3 >/dev/null
else
for i in $(seq 1 15); do
echo -en "\a" >/dev/tty0
sleep 0.05
done
fi
else
LogPrint "Speaker driver failed to load, no beeps, sorry !"
fi
fi
}